吸附劑式干燥的機

◆物料亮點 Product features

※都具有比較穩定相符的撒氣經濟壓力和露點

1.吸附劑塔之位置與直經經科學試驗報告單精密鑄造計算方法，塔床進而導致阻力小，切實保障了壓縮視頻廢氣非常干燥劑5秒的相處期限，夠滿足產品氣的露點耍求。

2.30％的常溫、干躁劑加工余量，用在補償金常溫、干躁劑的自然是老舊化，保障常溫、干躁。

3.中大型向外擴散器，狠抓熱空氣更加均勻使用低溫干燥劑層，解除溝流表現。

※回收利用氣量消耗不大于14％

1.有遠見的機筒設計構思，存為100％的過濾脂肪含量，存放的脂肪含量使用增強機體重復一階段的機體重復氣溫濕度，加快機器的解吸能力素質，導致機體重復更充分。

2.粗糙和可機體再生采用了返向平衡方案怎么寫，濕熱空氣走過干的樹脂吸附劑時效性果較好的。可機體再生氣進口含濕量操縱在亞達到飽和方式方式，使消音器原理器及res排氣車道無結霜現象之慮。

3.可據皮膚干燥機的開機運行負載電阻意愿調高機體恢復氣容量，狠抓機體恢復暖濕氣流持續保持穩定，機體恢復壓強低至臨界值。

※干躁劑使用的生命周期長

1.適合的的機筒寬度，使氣體實現干躁劑層的空氣流速和用時保護好的方式，完全起到干躁劑的能力。

2.合理安排的體統性能，在熱空氣邁入機筒前，經除油正確處理立刻清楚熱空氣中內油份物與重影響物，禁止烘干劑層受影響。

※機按照了新意高品行電動三輪及氣動系統閥和可信的全電商可程序設計序把控器，電腦用戶界面很友好，全自動陸續出現雙塔生產，循環系統期施工現場可編，出貨調節10min。閥體年限有50萬次運作。

※壓力容器封頭外壁作冷鍍鋅鐵皮防銹蝕治理，10年不銹跡。

※動做精確性、機械性能固定、操作步驟簡約，安裝程序不須基礎理論。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆重要技巧性能參數 Main technical parameters